[Tizen]Tizen systemctl 명령어 정리

systemctl [OPTIONS...] {COMMAND} ...

Query or send control commands to the systemd manager.

  -h --help           Show this help

     --version        Show package version

  -t --type=TYPE      List only units of a particular type

     --state=STATE    List only units with particular LOAD or SUB or ACTIVE stat

  -p --property=NAME  Show only properties by this name

  -a --all            Show all loaded units/properties, including dead/empty

                      ones. To list all units installed on the system, use

                      the 'list-unit-files' command instead.

     --reverse        Show reverse dependencies with 'list-dependencies'

  -l --full           Don't ellipsize unit names on output

     --fail           When queueing a new job, fail if conflicting jobs are

                      pending

     --irreversible   When queueing a new job, make sure it cannot be implicitly

                      cancelled

     --ignore-dependencies

                      When queueing a new job, ignore all its dependencies

     --show-types     When showing sockets, explicitly show their type

  -i --ignore-inhibitors

                      When shutting down or sleeping, ignore inhibitors

     --kill-who=WHO   Who to send signal to

  -s --signal=SIGNAL  Which signal to send

  -H --host=[USER@]HOST

                      Show information for remote host

  -P --privileged     Acquire privileges before execution

  -q --quiet          Suppress output

     --no-block       Do not wait until operation finished

     --no-wall        Don't send wall message before halt/power-off/reboot

     --no-reload      When enabling/disabling unit files, don't reload daemon

                      configuration

     --no-legend      Do not print a legend (column headers and hints)

     --no-pager       Do not pipe output into a pager

     --no-ask-password

                      Do not ask for system passwords

     --system         Connect to system manager

     --user           Connect to user service manager

     --global         Enable/disable unit files globally

     --runtime        Enable unit files only temporarily until next reboot

  -f --force          When enabling unit files, override existing symlinks

                      When shutting down, execute action immediately

     --root=PATH      Enable unit files in the specified root directory

  -n --lines=INTEGER  Numer of journal entries to show

  -o --output=STRING  Change journal output mode (short, short-monotonic,

                      verbose, export, json, json-pretty, json-sse, cat)

-----------------------------------------------------------------------------

-----------------------------------------------------------------------------

Unit Commands:

  list-units                      List loaded units

-----------------------------------------------------------------------------

  list-sockets                    List loaded sockets ordered by address

  start [NAME...]                 Start (activate) one or more units

  stop [NAME...]                  Stop (deactivate) one or more units

  reload [NAME...]                Reload one or more units

  restart [NAME...]               Start or restart one or more units

  try-restart [NAME...]           Restart one or more units if active

  reload-or-restart [NAME...]     Reload one or more units if possible,

                                  otherwise start or restart

  reload-or-try-restart [NAME...] Reload one or more units if possible,

                                  otherwise restart if active

  isolate [NAME]                  Start one unit and stop all others

  kill [NAME...]                  Send signal to processes of a unit

  is-active [NAME...]             Check whether units are active

  is-failed [NAME...]             Check whether units are failed

  status [NAME...|PID...]         Show runtime status of one or more units

  show [NAME...|JOB...]           Show properties of one or more

                                  units/jobs or the manager

  set-property [NAME] [ASSIGNMENT...]

                                  Sets one or more properties of a unit

  help [NAME...|PID...]           Show manual for one or more units

  reset-failed [NAME...]          Reset failed state for all, one, or more

                                  units

  list-dependencies [NAME]        Recursively show units which are required

 or wanted by this unit or by which

 this unit is required or wanted

-----------------------------------------------------------------------------

-----------------------------------------------------------------------------

Unit File Commands:

  list-unit-files                 List installed unit files

-----------------------------------------------------------------------------  

  enable [NAME...]                Enable one or more unit files

  disable [NAME...]               Disable one or more unit files

  reenable [NAME...]              Reenable one or more unit files

  preset [NAME...]                Enable/disable one or more unit files

                                  based on preset configuration

  is-enabled [NAME...]            Check whether unit files are enabled

  mask [NAME...]                  Mask one or more units

  unmask [NAME...]                Unmask one or more units

  link [PATH...]                  Link one or more units files into

                                  the search path

  get-default                     Get the name of the default target

  set-default NAME                Set the default target

-----------------------------------------------------------------------------

-----------------------------------------------------------------------------

Job Commands:

  list-jobs                       List jobs

-----------------------------------------------------------------------------

  cancel [JOB...]                 Cancel all, one, or more jobs

-----------------------------------------------------------------------------

-----------------------------------------------------------------------------

Snapshot Commands:

  snapshot [NAME]                 Create a snapshot

-----------------------------------------------------------------------------

  delete [NAME...]                Remove one or more snapshots

-----------------------------------------------------------------------------

-----------------------------------------------------------------------------

Environment Commands:

  show-environment                Dump environment

-----------------------------------------------------------------------------

  set-environment [NAME=VALUE...] Set one or more environment variables

  unset-environment [NAME...]     Unset one or more environment variables

-----------------------------------------------------------------------------

-----------------------------------------------------------------------------

Manager Lifecycle Commands:

  daemon-reload                   Reload systemd manager configuration

  daemon-reexec                   Reexecute systemd manager

-----------------------------------------------------------------------------

System Commands:

  default                         Enter system default mode

  rescue                          Enter system rescue mode

  emergency                       Enter system emergency mode

  halt                            Shut down and halt the system

  poweroff                        Shut down and power-off the system

  reboot [ARG]                    Shut down and reboot the system

  kexec                           Shut down and reboot the system with kexec

  exit                            Request user instance exit

  switch-root [ROOT] [INIT]       Change to a different root file system

  suspend                         Suspend the system

  hibernate                       Hibernate the system

  hybrid-sleep                    Hibernate and suspend the system

-----------------------------------------------------------------------------